Diseño de módulo entrenador de fibra óptica.
Fecha
2020-10-27
Autores
Título de la revista
ISSN de la revista
Título del volumen
Editor
Universidad de Guayaquil. Facultad de Ingeniería Industrial. Carrera de Ingeniería en Teleinformática.
Resumen
Usar equipos tecnológicos para el desarrollo académico es de vital importancia debido a
que se optimiza muchos procesos en la enseñanza. El presente trabajo de titulación tiene
como objetivo Diseñar un Módulo Entrenador De Fibra Óptica para uso en la materia de
Simulación de Sistemas en el laboratorio de Networking en la Carrera de Ingeniería en
Teleinformática de la Universidad de Guayaquil. Se utilizó el método bibliográfico para
decidir qué elementos son lo más adecuado para el envío y recepción de señales ópticos,
para la creación del diseño de los circuitos del módulo entrenador de fibra óptica. Para la
simulación de los diferentes circuitos que conforman el módulo se usó el método
experimental a través de pruebas experimentales por medio de simulaciones con la finalidad
de lograr resultados óptimos y, por último, se utilizó el método de investigación descriptiva
donde se registra el comportamiento de resultados y esquema de los circuitos usando los
símbolos más comunes como son las figuras. Se realizó pruebas de las señales de cada
circuito del módulo en sus salidas en dominio de tiempo y frecuencia mediante el software
Proteus dando como resultados una información fiable del 90% donde la información
transmitida llega a su destino final con ligeras variaciones como se puede observar en él
envió de audio por medio de láser donde la longitud de onda es más angosta a la enviada.
Se concluye que el diseño del módulo es de gran importancia en la educación, ya que ayuda
a comprender mejor el funcionamiento de las comunicaciones ópticas.
Using technological equipment for academic development is of vital importance because many processes in teaching are optimized. The objective of this degree work is to Design a Fiber Optic Trainer Module for use in the subject of Systems Simulation in the Networking laboratory in the Teleinformatics Engineering Degree at the University of Guayaquil. The bibliographic method was used to decide which elements are the most suitable for sending and receiving optical signals, for the creation of the circuit design of the fiber optic trainer module. For the simulation of the different circuits that make up the module, the experimental method was used through experimental tests by means of simulations in order to achieve optimal results and, finally, the descriptive research method was used where the behavior of results and circuit diagram using the most common symbols such as figures. The signals of each circuit of the module were tested in their outputs in time and frequency domain using the Proteus software, resulting in 90% reliable information where the transmitted information reaches its final destination with slight variations as can be seen in the sending of audio by means of laser where the wavelength is narrower than the one sent. It is concluded that the design of the module is of great importance in education as it helps to better understand the operation of optical communications.
Using technological equipment for academic development is of vital importance because many processes in teaching are optimized. The objective of this degree work is to Design a Fiber Optic Trainer Module for use in the subject of Systems Simulation in the Networking laboratory in the Teleinformatics Engineering Degree at the University of Guayaquil. The bibliographic method was used to decide which elements are the most suitable for sending and receiving optical signals, for the creation of the circuit design of the fiber optic trainer module. For the simulation of the different circuits that make up the module, the experimental method was used through experimental tests by means of simulations in order to achieve optimal results and, finally, the descriptive research method was used where the behavior of results and circuit diagram using the most common symbols such as figures. The signals of each circuit of the module were tested in their outputs in time and frequency domain using the Proteus software, resulting in 90% reliable information where the transmitted information reaches its final destination with slight variations as can be seen in the sending of audio by means of laser where the wavelength is narrower than the one sent. It is concluded that the design of the module is of great importance in education as it helps to better understand the operation of optical communications.
Descripción
Este documento contiene archivo en PDF
Palabras clave
TECNOLOGÍA DE LAS TELECOMUNICACION, COMUNICACIÓN ÓPTICA, FIBRA ÓPTICA, TELECOMUNICACIONES